Community Profile

photo

Martin

Last seen: 2 days ago Active since 2011

Statistics

All
  • Knowledgeable Level 3
  • Revival Level 3
  • 3 Month Streak
  • Knowledgeable Level 2
  • First Answer
  • Solver

View badges

Content Feed

View by

Answered
Simscape Tank (G-TL) Elevation from a reference
The best way may be to use the Pipe (TL) block in Simscape Fluids. Closed conduit that transports fluid between thermal liquid ...

6 months ago | 0

Answered
Why are my simulink initial conditions sometimes not met, despite high priority?
When selecting Start simulation from steady state, the solver tries to find what the model would go to after a very long simulat...

6 months ago | 0

Answered
How can I model an Elbow in Simspace while using the TL library?
Elbows are available in the Thermal Liquid library in Simscape Fluids as of R2022a. Pipe turn in a thermal liquid network - MAT...

6 months ago | 0

Answered
Interface (TL-IL) variable temperature
Thermal liquid elbows have been added as of R2022a. Pipe turn in a thermal liquid network - MATLAB (mathworks.com)

6 months ago | 0

Answered
Simulate interface between a Thermal Liquid and Two-Phase Fluid
Models heat exchange between a thermal liquid network and a network that can undergo phase change - MATLAB (mathworks.com) A mo...

6 months ago | 0

Answered
how do I use run-time parameter with simscape gas-charged accumulator
I know that this is an older question. As of a few years ago, all parameters in the Gas-charged Accumulator are run-time capable...

6 months ago | 0

Answered
How to access to two-phase fluid properties during run
This might be the block that you need: Measure temperature, density, specific enthalpy, specific entropy, and specific volume in...

6 months ago | 0

Answered
How can I simulate jamming fault at a certain time?
One possibility would be to use the Rotational Damper in Simscape Driveline: Linear rotational damper - MATLAB (mathworks.com) ...

6 months ago | 0

Answered
Simulink Model DC Motor with Transmission Gear
Please see Vehicle in Simscape Driveline and Simulink - MATLAB & Simulink (mathworks.com). It shows both Simulink and Simscape D...

6 months ago | 0

Answered
Problems with moving Simscape from 2014b to 2015b
MathWorks does not guarantee behavior when files are saved in a newer release and then opened on an older release. In this case,...

6 months ago | 0

Answered
Add Reset Function to Simscape Integrator Block
The PS Integrator was updated in R2021a to provide this functionality. The source code is available for that block as well. PS ...

1 year ago | 0

Answered
i want to learn about the oxygen concentrator example in simscape matlab ?
Hello Hassan, You can find information about it here: Oxygen Concentrator - MATLAB & Simulink (mathworks.com)

2 years ago | 0

Answered
Negative velocity curve from vehicle body block
Hi Vinay, It is difficult to say what happened, but it looks like recreating the subsystem worked. It may be possible that some...

2 years ago | 0

Answered
Source Code Condenser Code
Hi Rainer, A Condenser/Evaporator with two-phase fluid on one side and moist air on the other was introduced in R2019a. A Cond...

2 years ago | 0

Answered
Unexpected dog clutch disengagement behavior
Hello Frank, Thank you for including the example model to demonstrate the issue. The translational behavior of the shift link...

3 years ago | 1

Answered
Unable to open the following model in R2019a trial version.
Hi Sadeer, It looks like the installation is not complete, or the path is incorrect. Definitely contact technical support for...

3 years ago | 0

Answered
Simple gear model with load dependent efficiency
Hi Mahesh, The load-dependent efficiency model assumes that torque loss is equal to a constant value plus an additional loss ...

3 years ago | 0

Answered
How is inertia in planetary gear block calculated?
Hello David, Yes, connecting the carrier port would be the carrier inertia. The planet inertia is the sum of all the planet g...

3 years ago | 0

Answered
I am getting the following error in simscape driveline please help
Hello Mastrieo, This could be due to an overconstrained model. Check to see if you have conflicting parts of the model, for e...

3 years ago | 0

Answered
Thermal behaviour of Harmonic Drive Simulink
Hello Kotryna, Some of this may have been addressed in your other questions. I would also check the Solver Configuration bloc...

3 years ago | 0

Answered
Can't find 'Drive Cycle Source' blockset in Simcsape/Simulink.
Hello Rohan, The Drive Cycle Source is part of the Powertrain Blockset. Check to see if you have that product installed. M...

3 years ago | 0

| accepted

Answered
"First solve for initial conditions failed to converge." Thermal model
Hello Kotryna, The temperature on those blocks is a difference, not absolute. Also focus on specifying the differential varia...

3 years ago | 0

Answered
Initial temperature harmonic drive gear
Hi Kotryana, As a first step, I would look at the Variable Viewer to see what is met and what is not. In the toolstrip, selec...

3 years ago | 0

Answered
Generic engine oscillating output
Hi Stephen, This looks like the oscillation is due to the interactions between the slipping pullies in the two belt drives. I...

3 years ago | 0

Answered
Quarter model with tire (Magic Formula) SimScape Driveline
Hello Marcin, The H port is a translational conserving port associated with the hub of the tire. It should be associated with...

3 years ago | 0

| accepted

Answered
Is it usually used Simscape Driveline for designing the powertrain of a diesel-electric locomotive? Are there any examples about trains?
Hello Stefania, While we do not have any shipping examples regarding trains, users have successfully used Simscape Driveline ...

3 years ago | 0

Answered
How can i see the output torque of a gearbox
Hello Sree, If you need the value during simulation, you could add a Torque Sensor from the Simscape Foundation Library in se...

3 years ago | 0

Answered
Looking for Leadscrew model in library and not found.
Hello Orlando, Do you have Simscape Driveline installed? This block is in the Simscape Driveline library under Gears and Rota...

3 years ago | 0

| accepted

Answered
Torque vector must be arranged in strictly ascending order.
The block is not erroring because of the torque vector given on the Engine Torque tab. Speed is the independent vector that must...

4 years ago | 0

Answered
Disk Friction Clutch - OPEN clutch
Hello Berkan, There are two types of kinetic friction in the model. The kinetic friction of the clutch plates pushing against...

4 years ago | 0

Load more