photo

MULI


Last seen: 4 days ago Active since 2024

Followers: 1   Following: 0

Statistics

  • Knowledgeable Level 2
  • 3 Month Streak
  • First Answer

View badges

Feeds

View by

Answered
Synchronous machine model incorrectly initializes when taking into account saturation
Hi Solis, I understand that you are facing an issue with the initialization of a synchronous machine model when accounting for...

11 days ago | 1

| accepted

Answered
how can i account charge and discharge of battery in ev modeling.
Hi Gokarna, I understand that you are trying to model both the charge and discharge behaviour of a battery in an electric vehi...

11 days ago | 0

Answered
C2000 simulink reduces PWM frequency
Hi Hadia, I understand that you are experiencing an issue where PWM signal is expected to generate at frequency of 20kHz but o...

12 days ago | 0

Answered
Failed to read "n" uint8 value(s) from the device error while reading serial information.
Hi Andrew, I understand that you are experiencing intermittent errors when trying to read data from a scale via an RS232 conne...

12 days ago | 0

Answered
Saturation in Synchronous Machine Salient Pole
Hi Solis, I understand that you are facing an issue with the initialization of a synchronous machine model when accounting for...

12 days ago | 0

Answered
Saturation in Synchronous Machine Salient Pole
Hi Jakob, I understand that you are facing an issue related to the configuration of the saturation curve in a salient pole syn...

15 days ago | 0

Answered
ACD block for C2000 MCU doesn't follow the sampletime we have set
Hi Henrik, I understand that you are facing an issue with the ADC block on the F280025C LaunchPad. Despite setting a sample t...

17 days ago | 0

Answered
How can I obtain the negative sequence currents and voltages in the d and q axises for inverter control?
Hi Fater, I understand that when you are using a negative angle for abc to dqo transformation you are getting 2nd order harmon...

19 days ago | 0

Answered
Simulation of three-phase ferroresonances in Simulink Simscape Electrical - Specialized Power Systems
Hello Torben, I understand that you need to simulate three-phase ferroresonance in an electrical power supply network using S...

19 days ago | 0

| accepted

Answered
How to use parfor for access or link function of satellite communication?
Hi Ravi, I understand that you are facing an error where nodes belong to different ‘satelliteScenarios’ while using a ‘parfor’ ...

19 days ago | 0

Answered
Real-time control PLC connected to Simulink is faulty
Hi Hoang, It seems like the issue you are facing arises from the mismatch between the sampling rates of your system component...

22 days ago | 0

Answered
How to use Battery Pulse Analysis with both Discharge and Charge Pulses?
Hi Christopher, I understand that you are trying to analyse a dataset that includes both charge and discharge pulses, and you...

23 days ago | 0

Answered
NI9401 Pulse Generation and Digital Output same time
Hi Tugrul, I understand that you need to control a stepper motor using a TRINAMICS stepper controller with the NI 9401 module ...

23 days ago | 0

Answered
Can somebody help me to read data from the register using the TI I2C receive block (part of Embedded Coder Support Package for Texas Instruments C2000 Processors)
I understand that you are facing an issue in reading data from the LSM6DS3H inertial module using the TMS320F28035 Piccolo Micro...

24 days ago | 0

Answered
Issue with Serial Receive (Arduino Hardware) SIMULINK interfacing with Arduino Mega. "255"
Hi John, I understand that you are sending data from a computer to an Arduino Mega using a USB-to-TTL adapter. The data should...

26 days ago | 0

Answered
How to break a waveform waveform into its constituent harmonics using FFT and see the harmonic waveforms at each frequency?
Hi Rasula, I understand that you need to isolate and observe the waveform at different harmonic frequencies of a voltage signa...

1 month ago | 0

Answered
Enabled Subsystem does not reliably disable
Hi, I understand that the Enabled Subsystem sometimes stays on for two time points instead of one because of how Simulink hand...

1 month ago | 0

Answered
How to get accurate RPM using a Raspberry pi board with Simulink?
Hi Jorge, I understand you are facing an issue with timing for the RPM measurement in Simulink. To improve accuracy and handle...

1 month ago | 0

Answered
How to add Get function to the Simulink model generated code
Hi Oldirch, I understand that you are encountering errors when trying to generate code from your Simulink model when including...

1 month ago | 0

| accepted

Answered
Processing 5 input of matrices into a fuzzy logic system
Hi Berna, I understand that need to process your five input matrices to generate a 207x216 output matrix. You can follow the...

1 month ago | 0

Answered
How to get closed loop frequency response when MPC as a feedforward controller?
Hi Ayesha, I understand that you need to perform Bode plot analysis for a plant model with Proportional-Integral (PI) control ...

1 month ago | 0

Answered
USRP N210 rx() returning data vector with different length
Hi Diogo, The error you are encountering happens when the number of samples returned by `rx()’ (i.e., `len’) is not consistent...

1 month ago | 0

Answered
How can I make a connection from the ePWM block to the MOSFET driver of the invertor circuit in Simulink Matlab 2024a?  
I understand that you are working with the TI F280049C microcontroller to generate SPWM signals in Simulink and you need to conn...

2 months ago | 0

Answered
servo motor with PWM controller
Hi borboev, I understand you need to simulate a tracking drive with a PWM controller. You can follow the below steps to perfor...

2 months ago | 0

Answered
MATLAB Fault Analysis - "Continuous-time signals support faults only if its destinations are discrete" Error Command
Hi Krishna, I understand that you are getting an issue when you tried to trigger a fault using “Simulink Fault analyser”. “S...

2 months ago | 0

Answered
pv array mppt model doesn't work as expected
Hi Diana, I understand that in “PV array connected to buck-boost converter model”, the voltage is not being considered in the ...

2 months ago | 0

Answered
environment of a ROV in simscape
Hi Yasine, I understand that you have exported a model of a Remotely Operated Vehicle (ROV) from SolidWorks into a simulation ...

2 months ago | 0

Answered
Can any one help? how to develop the code or logic for electric vehicle charging and discharging limits as mentioned in picture and what should be the values of threshold.
Hi Imran, I understand that you are asking about the logic that controls the charging and discharging limits of electric vehic...

2 months ago | 0

| accepted

Answered
Issue with DTC of PMSM at 40kHz PWM Frequency
Hi MD, I understand that in "Direct Torque Control of PMSM Using Quadrature Encoder or Sensorless Flux Observer" example you a...

2 months ago | 0

Answered
Modeling of IEEE recommended Electrical Protection of Electrical Generator in Simulink
Hi Saqib, I understand that you are looking into the relays components, to implement electrical generator protection in Simuli...

2 months ago | 0

Load more