Community Profile

photo

Madhu Govindarajan


MathWorks

237 total contributions since 2014

I work as a Technical Marketing Engineer at the MathWorks and I focus on hardware connectivity with MathWorks tools. Prior to joining MathWorks, I interned with Honda R&D Americas while working towards a Masters degree in Mechanical engineering at The Ohio State University.

Contact

Madhu Govindarajan's Badges

  • 12 Month Streak
  • Knowledgeable Level 3
  • Revival Level 3
  • First Answer
  • Scavenger Finisher
  • Solver

View details...

Contributions in
View by

Answered
arduino engineering kit invalid i2c address formatt
Thanks for sending the output, the problem arises from the fact that you are using the old Arduino_Engineering_Kit_Hardware_Supp...

3 days ago | 1

| accepted

Answered
play a buzzer using arduino
Have an arduino connected to MATLAB using a = arduino command. After that, what is the output when you type the following: met...

5 days ago | 0

Answered
arduino engineering kit invalid i2c address formatt
The tutorial is still valid as I am using it in R2019a, so let's try and see where the error is coming from. Type the followin...

5 days ago | 1

Answered
Arduino i2c and pwm failure
Is it possible that you are not using an external battery to power these devices? I have had this happen to me sometimes when th...

5 days ago | 0

Answered
Cannot program board Nano3
I would recommend you try arduinosetup first and if that is successful, then connect with arduino using a=arduino instead of men...

10 days ago | 0

Answered
Arduino i2c and pwm failure
Which release of MATLAB are you using?

10 days ago | 0

Answered
Matlab Arduino support package
This feels like something went wrong with the support package installation. What is the output if you type which -all arduino in...

13 days ago | 0

Answered
Problem of adding LSM303 Library to matlab
Is it possible to communicate with the Arduino board without this library? Have you tried putting the board in bootloader mod...

13 days ago | 0

Answered
the Arduino UNO WiFi Rev 2
As per this link, this board is not supported. https://www.mathworks.com/hardware-support/arduino-simulink.html If you are lo...

17 days ago | 0

Submitted


Raspberry Pi®-based Indoor Climate Monitoring System
Example models needed for the Raspberry Pi®-based Indoor Climate Monitoring System project

17 days ago | 6 downloads |

Answered
Simulink Coder Deployment to ST Nucleo
I don't know about the second part of your question on how to reconfigure pins. To answer your first question, I don't think...

19 days ago | 0

Answered
Arduino MKR1000 + Simulink external mode over WiFi Speed
I have done it at 100 Hz on the Wi-Fi, but mine was a private Wi-Fi connection. I would say if you are on a public connection/on...

19 days ago | 0

Answered
Error shading - mobile rover - Arduino Engineering Kit
That variable should be heading. That is the problem.

24 days ago | 0

Submitted


Simulink library for Arduino Liquid Crystal Display
The Simulink block allows you to display text on a 16x2 character LCD screen connected to an Arduino

25 days ago | 56 downloads |

Answered
Error connecting Arduino hardware to MATLAB R2018b
Have you tried uninstalling and reinstalling the support package? When installing these support packages if additional terminal ...

27 days ago | 0

Answered
"measure temperature from i2c device using arduino hardware".
Can you try with other arduino boards or other sensors? That code works for me on the Arduino and TMP102 sensor.

30 days ago | 0

Answered
"measure temperature from i2c device using arduino hardware".
What is the Arduino board using and does your hardware setup look similar to the one shown here - https://www.mathworks.com/help...

1 month ago | 0

Answered
The problem of delay in contact with Ardiono
When you attempt to open a connection with Arduino, MATLAB downloads an Arduino sketch to the hardware and this is the reason it...

1 month ago | 0

Answered
matlab function for arduino
I think you are better off using the Simulink workflow to perform controls and not use the MATLAB Support package for Arduino fu...

1 month ago | 0

Answered
matlab function for arduino
Based on the error it looks like you are attempting to use MATLAB Function block within a Simulink Model. In this approach, you ...

1 month ago | 0

Answered
Recording values from I2C sensors
If you use MATLAB Support Package for Arduino, there is readRegister function to read data in - https://www.mathworks.com/help/s...

1 month ago | 0

Answered
Can't connect Arduino Uno (Genuino) to Matlab R2016a
Try putting the device in bootloader mode, by double presssing the RESET button.

1 month ago | 0

Answered
How to read COM port caption
seriallist command is used to detect additions to the COM port #s (only available starting R2017a). However in this technique yo...

2 months ago | 1

Answered
How I can read data from VL53L0X in simulink?
I would recommend creating your own block using the techniques described in this video - https://www.youtube.com/watch?v=qoj8Pa2...

2 months ago | 1

| accepted

Answered
Raspberry pi board connecting to matlab
So I am assuming this is right after MATLAB Support package for Raspberry Pi Setup. If it fails, I usually try the following - ...

2 months ago | 0

Answered
Arduino Temperature Sensor with buttons
If you need your code to be deployed to the Arduino and work independent of PC, then use Simulink Support Package for Arduino. I...

2 months ago | 0

Answered
Servo Library with Simulink and Arduino
This video has some relevant items - https://www.youtube.com/watch?v=qoj8Pa2wi0A but needs to be adapted for your case

2 months ago | 0

Answered
No connection to mkr1000 board.
Try putting the Arduino in bootloader mode before downloading the Simulink model and also make Simulink automatically set COM po...

2 months ago | 0

Answered
How do i plot ECG sensor data from arduino to ECG graph using matlab?
Here are my thoughts on this topic and unfortunately I am not a subject matter expert on this. https://www.mathworks.com/video...

2 months ago | 0

Answered
How do i plot ECG sensor data from arduino to ECG graph using matlab?
You can search through the MATLAB File Exchange to see if there are pre-existing libraries that you can use. If not, you will ha...

2 months ago | 0

Load more