Submitted
Fuel Cell Vehicle Model in Simscape
Fuel cell electric vehicle with battery model and cooling system.
5 months ago | 4788 downloads |
Submitted
Four Bar Linkage Optimization in Simscape
Four-bar linkage lengths are optimized using MATLAB to follow a desired trajectory.
5 months ago | 2319 downloads |
Submitted
Forklift Design with Simscape
Test forklift stability. Vary load and mast position and find stability limit in static and dynamic tests.
5 months ago | 93 downloads |
Submitted
Flexible Body Models in Simscape Multibody
Lumped parameter and state-space methods for static, modal, and dynamic analysis
5 months ago | 4200 downloads |
Submitted
Excavator Design with Simscape
Design an excavator. Define pin locations, calculate BOF and TOF, produce load charts, and simulate dig cycles.
5 months ago | 1511 downloads |
Submitted
Boom Lift Model in Simscape
Telescoping boom lift with tread drive.
5 months ago | 597 downloads |
Submitted
Electric Aircraft Model in Simscape
Electric and hybrid electric aircraft models for component sizing
5 months ago | 2634 downloads |
Submitted
Dual Clutch Transmission Model in Simulink
Dual-clutch transmission with MATLAB scripts for optimizing the shift schedule.
5 months ago | 7061 downloads |
Submitted
Aileron Model in Simscape
Actuator with ideal, hydraulic, and electrical designs.
5 months ago | 4387 downloads |
Submitted
Backhoe Model in Simscape
Backhoe model, including hydraulic actuators for arm and bucket tilt, and multibody dynamics.
5 months ago | 6675 downloads |
Answered
vehicle dynamics code problems
Hi Bradford - I was unable to reproduce this error message. Normally, that means the variable t is not defined in the scope wer...
vehicle dynamics code problems
Hi Bradford - I was unable to reproduce this error message. Normally, that means the variable t is not defined in the scope wer...
8 months ago | 0
Submitted
Medical Ventilator Model in Simscape
Positive-pressure medical ventilator system using Simscape™
9 months ago | 1122 downloads |
Answered
Where can I find the V2Glib library for Simulink?
That library was renamed to renamed to VehicletoGridSystemLib.slx. It is part of an example. In R2025a or earlier, run this co...
Where can I find the V2Glib library for Simulink?
That library was renamed to renamed to VehicletoGridSystemLib.slx. It is part of an example. In R2025a or earlier, run this co...
11 months ago | 0
Submitted
Simscape Multibody Model from MATLAB Code
MATLAB code to build a Simscape Multibody model of a single link and a multi-link pendulum
11 months ago | 2177 downloads |
Submitted
Onshape CAD Export to Simscape Multibody
Export Onshape CAD assembly to Simscape Multibody, including part and joint information.
1 year ago | 1241 downloads |
Answered
Kann man in Simscape ein Feder-Stößel-System simulieren
Es ist nicht genau dasselbe, aber dieses Beispielmodell, das mit Simscape Multibody geliefert wird, ist sehr ähnlich. https://w...
Kann man in Simscape ein Feder-Stößel-System simulieren
Es ist nicht genau dasselbe, aber dieses Beispielmodell, das mit Simscape Multibody geliefert wird, ist sehr ähnlich. https://w...
1 year ago | 0
Answered
Simulation of crystal oscillator circuit a Simscape does not converge
While I can't say for sure what is going wrong, if I set Rf to 1e9 the simulation runs to completion and the value on the Scope ...
Simulation of crystal oscillator circuit a Simscape does not converge
While I can't say for sure what is going wrong, if I set Rf to 1e9 the simulation runs to completion and the value on the Scope ...
1 year ago | 0
Answered
How do i know which switch should i use in Simulink?
To use Simulink signals to control inputs to Simscape blocks, you often need this converter block https://www.mathworks.com/hel...
How do i know which switch should i use in Simulink?
To use Simulink signals to control inputs to Simscape blocks, you often need this converter block https://www.mathworks.com/hel...
1 year ago | 0
| accepted
Submitted
Aircraft Power Network in Simscape Electrical
Aircraft Power Network in Simscape Electrical with AC and DC networks
2 years ago | 4272 downloads |
Answered
Does MATLAB have four in-wheel motor Electric vehicle model, where one motor control one wheel independently. Sometimes called 4-Indepdendent Drive EV, 4 In-wheel motor EV
Take a look at this File Exchange submission: https://www.mathworks.com/matlabcentral/fileexchange/172279-formula-student-vehic...
Does MATLAB have four in-wheel motor Electric vehicle model, where one motor control one wheel independently. Sometimes called 4-Indepdendent Drive EV, 4 In-wheel motor EV
Take a look at this File Exchange submission: https://www.mathworks.com/matlabcentral/fileexchange/172279-formula-student-vehic...
2 years ago | 0
Answered
How to check with different C rates of battery model in Simulink
To modify the C rate, you will need to modify the level of current drawn from the battery. You can use a Controlled Current Sou...
How to check with different C rates of battery model in Simulink
To modify the C rate, you will need to modify the level of current drawn from the battery. You can use a Controlled Current Sou...
2 years ago | 0
Answered
I am trying to implement Li-Ion battery model in Simulink. I want to measure temperature inside model in real-time and also figure out changes in it with variable voltage supply. Can anyone give me reference of this model and how to simulate it ??
I recommend you look at the Battery Pack Builder in Simscape Battery. It helps you assemble battery packs and construct a test ...
I am trying to implement Li-Ion battery model in Simulink. I want to measure temperature inside model in real-time and also figure out changes in it with variable voltage supply. Can anyone give me reference of this model and how to simulate it ??
I recommend you look at the Battery Pack Builder in Simscape Battery. It helps you assemble battery packs and construct a test ...
2 years ago | 0
Answered
Battery soc is not working as expected in different file it shows different variation in soc can any one help this out ...
The parameters are only a portion of what affects the SOC during a simulation. The systems on the grid, test profile, and solve...
Battery soc is not working as expected in different file it shows different variation in soc can any one help this out ...
The parameters are only a portion of what affects the SOC during a simulation. The systems on the grid, test profile, and solve...
2 years ago | 0
Answered
V2G matlab exemple
In https://www.mathworks.com/help/sps/ug/24-hour-simulation-of-a-vehicle-to-grid-v2g-system.html, the scopes are plotting the ac...
V2G matlab exemple
In https://www.mathworks.com/help/sps/ug/24-hour-simulation-of-a-vehicle-to-grid-v2g-system.html, the scopes are plotting the ac...
2 years ago | 0
Answered
In simscape for lead acid battery cell how can i calculate and assign values for main branch and paracetic branch values
Typically you would obtain measurement data and use parameter estimation techniques. Take a look at this example to see the pro...
In simscape for lead acid battery cell how can i calculate and assign values for main branch and paracetic branch values
Typically you would obtain measurement data and use parameter estimation techniques. Take a look at this example to see the pro...
2 years ago | 0
Answered
Simscape Torque Sensor output is zero
Your angular motion sensor should be connected between shaft and a Mechanical Rotational Reference (NOT in series). Your torque...
Simscape Torque Sensor output is zero
Your angular motion sensor should be connected between shaft and a Mechanical Rotational Reference (NOT in series). Your torque...
2 years ago | 1
| accepted
Answered
Does anyone know why I get an error when I run the fuel cell model for about 18000s?
The error message you encountered is because the test conditions for the fuel cell are not suitable for 18000 seconds. The driv...
Does anyone know why I get an error when I run the fuel cell model for about 18000s?
The error message you encountered is because the test conditions for the fuel cell are not suitable for 18000 seconds. The driv...
3 years ago | 1
Submitted
Vehicle Model with Delft-Tyre in Simscape Multibody
Vehicle model in Simscape Multibody using 3-D tire model.
3 years ago | 6459 downloads |
Answered
How to avoid adding the striking mass to the robot body mass during a collision test in simscape?
A really good way to do this is to use Simscape Multibody. With Simscape Multibody you can model contact forces between differe...
How to avoid adding the striking mass to the robot body mass during a collision test in simscape?
A really good way to do this is to use Simscape Multibody. With Simscape Multibody you can model contact forces between differe...
3 years ago | 0
Answered
Battery box in Simscape
Hi Bence, You can model a housing for your battery modules that prevents heat transfer between the modules. This could be pass...
Battery box in Simscape
Hi Bence, You can model a housing for your battery modules that prevents heat transfer between the modules. This could be pass...
3 years ago | 0
| accepted