looptuneOptions

Set options for looptune

expand all in page

Description

Use looptuneOptions to create an option set for the looptune function.

Creation

options = looptuneOptions returns the default option set for the looptune command.

options = looptuneOptions(Name,Value) creates an option set and sets Properties using one or more name-value arguments

Properties

expand all

Target gain margin, in decibels, specified as a scalar. GainMargin specifies the required gain margin for the tuned control system. For MIMO control systems, the gain margin is the multiloop disk margin. See Stability Analysis Using Disk Margins (Robust Control Toolbox) for the definition of the multiloop disk margin.

Target phase margin, in degrees, specified as a scalar. PhaseMargin specifies the required phase margin for the tuned control system. For MIMO control systems, the phase margin is the multiloop disk margin. See Stability Analysis Using Disk Margins (Robust Control Toolbox) for the definition of the multiloop disk margin.

Amount of information to display during looptune runs, specified as one of these values:

  • 'off' — Run in silent mode, displaying no information during or after the run.

  • 'iter' — Display optimization progress after each iteration. The display includes the value of the objective parameter gam after each iteration. The display also includes a Progress value, indicating the percent change in gam from the previous iteration.

  • 'final' — Display a one-line summary at the end of each optimization run. The display includes the minimized value of gam and the number of iterations for each run.

Maximum number of iterations in each optimization run, specified as a positive scalar.

Number of additional optimizations starting from random values of the free parameters in the controller, specified as a nonnegative scalar.

If RandomStart = 0, looptune performs a single optimization run starting from the initial values of the tunable parameters. Setting RandomStart = N > 0 runs N additional optimizations starting from N randomly generated parameter values.

looptune tunes by finding a local minimum of a gain minimization problem. To increase the likelihood of finding parameter values that meet your design requirements, set RandomStart > 0. You can then use the best design that results from the multiple optimization runs.

Use with UseParallel = true to distribute independent optimization runs among MATLAB® workers (requires Parallel Computing Toolbox™ software).

Option to enable parallel computing, specified as the comma-separated pair consisting of 'UseParallel' and false or true.

When you use the RandomStart option to run multiple randomized optimization starts when tuning a structured controller, you can also use parallel computing to distribute the optimization runs among workers in a parallel pool. When you set this option to true, if there is an available parallel pool, then the software performs independent optimization runs concurrently among workers in that pool. If no parallel pool is available, one of the following occurs:

  • If you select Automatically create a parallel pool in your Parallel Computing Toolbox preferences (Parallel Computing Toolbox), then the software starts a parallel pool using the settings in those preferences.

  • If you do not select Automatically create a parallel pool in your preferences, then the software performs the optimization runs successively, without parallel processing.

Using parallel computing requires Parallel Computing Toolbox software.

Target value for the objective parameter gam, specified as a scalar.

The looptune command converts your design requirements into normalized gain constraints. The command then tunes the free parameters of the control system to drive the objective parameter gam below 1 to enforce all requirements.

The default TargetGain = 1 ensures that the optimization stops as soon as gam falls below 1. Set TargetGain to a smaller or larger value to continue the optimization or start sooner, respectively.

Relative tolerance for termination, specified as a scalar.

The optimization terminates when the objective parameter gam decreases by less than TolGain over 10 consecutive iterations. Increasing TolGain speeds up termination, and decreasing TolGain yields tighter final values.

Maximum closed-loop natural frequency, specified as a positive scalar.

Setting MaxFrequency constrains the closed-loop poles to satisfy |p| <  MaxFrequency.

To allow looptune to choose the closed-loop poles automatically, based upon the system's open-loop dynamics, set MaxFrequency = Inf. To prevent unwanted fast dynamics or high-gain control, set MaxFrequency to a finite value.

Specify MaxFrequency in units of 1/TimeUnit, relative to the TimeUnit property of the system you are tuning.

Minimum decay rate for closed-loop poles, specified as a positive scalar

Constrains the closed-loop poles to satisfy Re(p) < -MinDecay. Increase this value to improve the stability of closed-loop poles that do not affect the closed-loop gain due to pole/zero cancellations.

Specify MinDecay in units of 1/TimeUnit, relative to the TimeUnit property of the system you are tuning.

Examples

collapse all

Open Live Script

Create an options set for a looptune run using three random restarts. Also, set the target gain and phase margins to 6 dB and 50 degrees, respectively, and limit the closed-loop pole magnitude to 100. 

options = looptuneOptions('RandomStart',3','GainMargin',6,...
                'PhaseMargin',50,'SpecRadius',100);

Alternatively, use dot notation to set the values of options. 

options = looptuneOptions;
options.RandomStart = 3;
options.GainMargin = 6;
options.PhaseMargin = 50;
options.SpecRadius = 100;

Configure an option set for a looptune run using 20 random restarts. Execute these independent optimization runs concurrently on multiple workers in a parallel pool.

If you have the Parallel Computing Toolbox software installed, you can use parallel computing to speed up looptune tuning of fixed-structure control systems. When you run multiple randomized looptune optimization starts, parallel computing speeds up tuning by distributing the optimization runs among workers.

If Automatically create a parallel pool is not selected in your Parallel Computing Toolbox preferences (Parallel Computing Toolbox), manually start a parallel pool using parpool (Parallel Computing Toolbox). For example:

parpool;

If Automatically create a parallel pool is selected in your preferences, you do not need to manually start a pool.

Create a looptuneOptions set that specifies 20 random restarts to run in parallel.

options = looptuneOptions('RandomStart',20,'UseParallel',true);

Setting UseParallel to true enables parallel processing by distributing the randomized starts among available workers in the parallel pool.

Use the looptuneOptions set when you call looptune. For example, suppose you have already created a plant model G0 and tunable controller C0. In this case, the following command uses parallel computing to tune the control system of G0 and C0 to the target crossoverwc. 

[G,C,gamma] = looptune(G0,C0,wc,options);

Version History

Introduced in R2011b

expand all

See Also

| (Simulink Control Design) | (Robust Control Toolbox)

Topics