remove DC component of real time signal
75 views (last 30 days)
Show older comments
I am using a interface for acquiring a signla in matlab.
The signal is sampled at 500Hz. I have to remove the DC component in real time.
How can I do that?
I know that simulink has the DC blocker block, but I need to accomplish this inside a matlab routine!
0 Comments
Answers (1)
Star Strider
on 14 Nov 2023
The D-C component is the mean of the signal, so for a recorded signal, simply subtract the mean.
Otherwise, since the D-C offsset is defined as having a frequency of zero (rad/s, Hz, or anything else), a highpass filter (or bandpass filter) with its passband (or lower passband) slightly above zero should remove the D-C offset. The resulting signal should then have a zero D-C offset.
5 Comments
Star Strider
on 14 Nov 2023
This is a difficult filter to realise because the lower transition region is too steep. I can make it work with a lower attenuation (35 dB rather than 50 dB) for ‘Rs’ and then it distorts the filtered signal significantly less. I encourage you to experiment with various passband, stopband, and atttenuation values to get the result you want.
Fs = 500; % Sampling Frequency (Hz)
Fn = Fs/2; % Nyquist Frequency (Hz)
Wp = [0.25 4.0]/Fn; % Passband Frequency (Normalised)
Ws = [0.01 5.0]/Fn; % Stopband Frequency (Normalised)
Rp = 1; % Passband Ripple
Rs = 35; % Passband Ripple (Attenuation)
[n,Wp] = ellipord(Wp,Ws,Rp,Rs); % Elliptic Order Calculation
[z,p,k] = ellip(n,Rp,Rs,Wp); % Elliptic Filter Design: Zero-Pole-Gain
[sos,g] = zp2sos(z,p,k); % Second-Order Section For Stability
figure
freqz(sos, 2^16, Fs) % Filter Bode Plot
set(subplot(2,1,1), 'XLim',[0 10]) % Zoom To Region-Of-Interest
set(subplot(2,1,2), 'XLim',[0 10])
L = 10*30;
t = linspace(0, Fs*L, Fs*L+1).'/Fs;
signal = sum(sin(2*pi*t.*[0.1:0.1:5 10:10:240]),2);
filtered_signal = filtfilt(sos,g,signal);
figure
plot(t, signal, 'DisplayName','Original')
hold on
plot(t, filtered_signal, 'DisplayName','Filtered')
hold off
xlabel('Time (s)')
ylabel('Amplitude')
legend('Location','best')
[FTsignal,Fv] = FFT1(signal, t);
[FTfiltered_signal,Fv] = FFT1(filtered_signal,t);
figure
plot(Fv, abs(FTsignal)*2, 'DisplayName','Original')
hold on
plot(Fv, abs(FTfiltered_signal)*2, 'DisplayName','Filtered')
hold off
grid
xlim([0 5])
xlabel('Frequency (Hz)')
ylabel('Magnitude')
legend('Location','best')
function [FTs1,Fv] = FFT1(s,t)
s = s(:);
t = t(:);
L = numel(t);
Fs = 1/mean(diff(t));
Fn = Fs/2;
NFFT = 2^nextpow2(L);
FTs = fft((s - mean(s)).*hann(L), NFFT)/sum(hann(L));
Fv = linspace(0, 1, NFFT/2+1)*Fn;
Iv = 1:numel(Fv);
FTs1 = FTs(Iv);
end
.
See Also
Categories
Find more on Audio Processing Algorithm Design in Help Center and File Exchange
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!