Statistics
0 Questions
17 Answers
RANK
3,385
of 300,918
REPUTATION
16
CONTRIBUTIONS
0 Questions
17 Answers
ANSWER ACCEPTANCE
0.00%
VOTES RECEIVED
0
RANK
of 21,110
REPUTATION
N/A
AVERAGE RATING
0.00
CONTRIBUTIONS
0 Files
DOWNLOADS
0
ALL TIME DOWNLOADS
0
RANK
of 171,685
CONTRIBUTIONS
0 Problems
0 Solutions
SCORE
0
NUMBER OF BADGES
0
CONTRIBUTIONS
0 Posts
CONTRIBUTIONS
0 Public Channels
AVERAGE RATING
CONTRIBUTIONS
0 Discussions
AVERAGE NO. OF LIKES
Feeds
Touchgfx integration with Simulink in matlab
Hi Jerry, Refer: SIMULINK with STM32 - MATLAB Answers - MATLAB Central Thanks, Madhu
13 hours ago | 0
Problem with UDP communication while configuring stm32nucleo using cubemx in Simulink
Please refer STM32H753ZI: Simulink UDP/TCP blocks fail due to Ethernet DMA buffer address requirement (0x30040200) - MATLAB An...
13 hours ago | 0
STM32H753ZI: Simulink UDP/TCP blocks fail due to Ethernet DMA buffer address requirement (0x30040200)
Hi, For the R2024b release, the supported version of CubeMX is 6.4.0. It is strongly recommended to use this version with MATLA...
13 hours ago | 0
Registration of STM32CubeMX Tool Without Internet-Based Third-Party Tools Installation
Hi, Kindly contact Technical Support for further assistance: https://in.mathworks.com/support/contact_us.html Thank you, Mad...
22 days ago | 0
LIN support for STM32 microcontroller series
Hi, Currently, LIN communication support is not available as a built-in block for STM32 . However, you can create your own cus...
2 months ago | 0
| accepted
SIMULINK with STM32
Hi Jerry, As Nidhi mentioned, display peripherals are currently not supported at present. However you can use custom code bloc...
2 months ago | 0
STM32F4xx Error:External Mode Open Protocol Connect command failed
Hi, It looks like you’re experiencing an external mode connection failure, which might be caused by selecting the wrong COM po...
6 months ago | 0
STM32 NUCLEO H753ZI Mqtt Simulink block is not sending.
Hi, Kindly contact Technical Support for further assistance: https://in.mathworks.com/support/contact_us.html Ensure that the...
7 months ago | 0
Unable to Programm stm Microcontroller.
Hi, There can be two workaround for the above issue: Instead of going through the Hardware Setup Screen, can you download the ...
2 years ago | 0
Gettting an error when trying to run the "Exchanging WiFi Data and Using ThingSpeak with STM32L475VG Discovery Board" MatLab example
Hi , I tried running the example at my end. It works fine without any error. Make sure the wifi setup and configuration paramet...
2 years ago | 0
Waijung Blockset Cannot Be Compiled
Hi Serhat, Wijung blockset is not supported by MathWorks , please post in respective channel for the same. Alternatively, you c...
2 years ago | 0
Code generation from Simulink to STM32F103 Processor.
Hi Nandini, STM32/MAT target is obsolete and not supported with the latest versions of MATLAB as mentioned here: https://www.st...
2 years ago | 0
| accepted
Embedded Coder support packages for STM32
Currently it is not supported , but you can develop the custom blocks depending on requirement. As device driver development is...
2 years ago | 0
Embedded Coder support package for STM32
Currently it is not supported , but you can develop the custom blocks depending on requirement. As device driver development is...
2 years ago | 0
STM32F411 Discovery board Blink LED program error
Hi, The STM32F4-Discovery board, specifically utilizing the STM32F407VG microcontroller, is officially supported according to t...
2 years ago | 0
| accepted
FPGA in the Loop minimum clock frequency
To get FPGA simulation with a small clock frequency, try increasing oversampling factor of the design. The Oversampling factor d...
3 years ago | 0
| accepted
Need help with Fourier Transform of a function
For this case, it is not necessary to get x(t). If y(t) = x(t) .[cos(t/2) + cos(3t/2)] and if x(jw) is known , then using conv...
3 years ago | 0
