photo

Juan Sagarduy

Last seen: 1 month ago Active since 2020

Followers: 1   Following: 0

Message

Statistics

All
  • 5-Star Galaxy Level 4
  • Personal Best Downloads Level 4
  • 6 Month Streak
  • Knowledgeable Level 4
  • Commenter
  • Solver
  • Revival Level 3
  • First Answer
  • First Submission

View badges

Feeds

View by

Submitted


Soft Starter Induction Motor Model
Electro-mechanical model of a thyristor-based soft starter with Simscape Electrical

2 months ago | 46 downloads |

Thumbnail

Submitted


Green Hydrogen (Wind & Solar) from (Alkaline) Electrolysis.
Simscape electrolyzer converting water and electricity (wind/solar renewable sources) into H2 gas. Alkaline technology included....

4 months ago | 205 downloads |

Thumbnail

Submitted


EV Charging with Renewable Energy / Micro-Grid Operation.
EV charging hubs featuring grid autonomy, energy storage and renewable (wind, solar) supply. Energy management in an off shore ...

1 year ago | 141 downloads |

Thumbnail

Submitted


E-mobility - Regenerative Braking - Off-road Motion
Simulation kit to study grid resilience, perform regenerative braking and motion over uneven terrain. Fault management is also f...

1 year ago | 31 downloads |

Thumbnail

Submitted


Fuel Cell-Battery Driven Electric Motor & Hydrogen Transfer
Electric Motor fed by Fuel Cell-Battery. Calibration based on I-V Datasheet Curve. Thermodynamic Analysis of Hydrogen Transport....

2 years ago | 47 downloads |

Thumbnail

Submitted


Servo-driven Pump Applications & Water Hammer Pressure Waves
Animation of a Hydraulic Pressure Wave & VFD pump applications for fluid transport (multi-tank system).

2 years ago | 22 downloads |

Thumbnail

Answered
How to input [Po Qo] and [np np] as a timeseries to a Three-Phase Dynamic Load block?
Hi there You have two ways of using the PQ block. In the first case, the dynamic profile of the load is determined by the initi...

3 years ago | 0

Answered
PV array with grid system with battery charger
Hi there The synchronization is done through a PLL block that senses the voltage of the grid and obtains the phase angle to be ...

3 years ago | 0

Answered
Replace a generic engine with a synchronous machine
Hello Sebastian Based on your description, I believe that the Motor & Drive System Level block (see link below) comes closest t...

3 years ago | 1

| accepted

Answered
Control of Vienna rectifier
Hi there Please check this demo https://se.mathworks.com/help/physmod/sps/ug/vienna_rectifier.html Using the Simscape Elec...

3 years ago | 0

Answered
Simcape simulation won't start due to "Model not assembled: position violation" error, how do I fix it?
Hi Lovre This is an indication that the kinematics in your mechanism are not physically possible. If the model is not too compl...

3 years ago | 0

Answered
Simscape Multibody: Zero crossing in control loop
Hi Irina It looks like you are allocating the angles in a closed loop (sign dependent) and then forcing a kinematic behaviour...

3 years ago | 1

| accepted

Answered
How do I attach blocks from the foundational library of simulink to the multibody blocks of simulink?
Hi Roberto Please check out the link below to solve the issue you named. https://se.mathworks.com/help/physmod/simscape/re...

3 years ago | 0

| accepted

Answered
fft analysis tool in powergui doesn't work
Hi there you need to open the FFT tool in a model with an electric model where you have previously saved current or voltage i...

3 years ago | 0

Answered
Two-Phase Fluid Properties (2P) for Helium
Hello Saara Unfortunately not. The way to do it would be through the two phase fluid settings block (Simscape Foundation Libr...

3 years ago | 0

| accepted

Answered
Simscape Multibody Contact Forces Mecanum Wheels
Hi there When look at the wheels, it looks like they are made of transversal cylinders on the perimeter. Rolling would be dis...

3 years ago | 1

| accepted

Answered
How to create contact between wheel and floor while making the wheel roll on the floor ?
Hi there Definitely, using the spatial force contact block would be the best option. See the submission below with an impleme...

3 years ago | 0

| accepted

Answered
how to make the small ball slide into the groove in simscape
Hello there I gave the mechanism a good try. It is all about positioning components with precision and then use the spatial for...

3 years ago | 1

| accepted

Answered
How can I plug inverse kinematics to a Simscape multibody?
Hello there You need to set the joint in kinematic mode (Actuation >> Motion - Prescribed / Torque - automatically calculated...

3 years ago | 0

Answered
Adding contact blocks to a model imported from Inventer into Simscape
Hi there You need a spatial force contact block taking in both geometries to resolve the contact. Modeling Contact Force Betwee...

3 years ago | 0

| accepted

Answered
Fuel Cell to Battery
Hello Mateo Many years have gone but this type of system is more actual than ever. Please see the link below: https://www....

3 years ago | 0

Answered
Using fuel cell stack and battery with electrical domain
Hi Hugo, An alternative you can think of is to do everything in Simscape. The link below may be helpful. This complements Jav...

3 years ago | 0

Answered
how to make a hydrogen fuel cell and battery hybrid to power a motor simulink
Hello Serge, You will find the link below interesting to tackle your question. https://www.mathworks.com/matlabcentral/fil...

3 years ago | 0

Answered
import multiple step files into simscape
Hi there Kim You shall export the geometry in the File Solid blocks and then use Spatial Force Contact blocks between solids....

3 years ago | 1

| accepted

Answered
how to determine base equation of heat flow rate sensor to calculate the heat generated by battery pack in simscape fluids
Hi there Please check out this submission. It captures cooling of Battery packs really well. https://www.mathworks.com/mat...

3 years ago | 0

Answered
Simscape Driveline Ideal Motion Sensor - Calculating Acceleration
Hi Peter This is good feedback, maybe there should that option in the sensor. But this can be solved by adding that into a mo...

3 years ago | 0

Answered
Moist Air Modeling error: Solver was unable to reduce the step size
Hello Guangwei I think the model may have some issues. It looks like you are filling/emptying the chamber. This leads in the ...

3 years ago | 0

| accepted

Answered
How to add or fix a spring in simscape Multibody?
Hi there Please check the link Interface between mechanical translational networks and Simscape Multibody joints - MATLAB (math...

3 years ago | 0

| accepted

Answered
Kinematic Analysis of 5dof Manipulaor Arm Simscape MultiBody
Hi Joe, Cool to see that you use Simscape Multibody. You need to set the joints in kinematic mode to accomodate the prescribed ...

3 years ago | 0

| accepted

Answered
Contact Modelling: Possible to model a vehicle driving over an 'obstacle course'?
Hello Rory I'd like to give this question a shot. The contact between the tires and uneven terrain can be modelled in the lates...

3 years ago | 0

Load more