Rationalfactor samplerate converter specification
D = fdesign.rsrc(L,M)
D = fdesign.rsrc(L,M,RESPONSE)
D = fdesign.rsrc(L,M,CICRESPONSE,D)
D = fdesign.rsrc(L,M,RESPONSE,SPEC)
D = fdesign.rsrc(L,M,SPEC,specvalue1,specvalue2,...)
D = fdesign.rsrc(...,Fs)
D = fdesign.rsrc(...,MAGUNITS)
D = fdesign.rsrc(L,M)
constructs
a rationalfactor samplerate filter specification object D
with
the InterpolationFactor
property equal to the positive
integer L
, the DecimationFactor
property
equal to the positive integer M
and the Response
property
set to 'Nyquist'
. The default values for the transition
width and stopband attenuation in the Nyquist design are 0.1π
radians/sample and 80 dB. If L
is unspecified, L
defaults
to 3. If M
is unspecified, M
defaults
to 2.
D = fdesign.rsrc(L,M,RESPONSE)
constructs
an rationalfactor samplerate converter with the interpolation factor L
,
decimation factor M
, and the response you specify
in RESPONSE
.
D = fdesign.rsrc(L,M,CICRESPONSE,D)
constructs
a CIC or CIC compensator rationalfactor samplerate convertor filter
specification object with the 'RESPONSE'
property
equal to 'CIC'
or 'CICCOMP'
. D
is
the differential delay. The differential delay, D
,
must precede the filter specification.
Because you are designing multirate filters, the specification options available are not the same as the specification options for designing singlerate filters. The interpolation and decimation factors are not included in the specification. Different filter responses support different specifications. The following table lists the supported response types and specification options. These options are not case sensitive.
Design Method  Valid Specification Options 

 See

 See

 See

 See


To
specify a CIC rationalfactor samplerate convertor, include the differential
delay after 
 See
To specify a CIC compensator rationalfactor
samplerate convertor, include the differential delay after 


'Gaussian' 
The filter specification must be preceded
by an integervalued 
 See
If you use the quasilinear IIR design
method, 
 See

 See

 See

 See

 See

 See

D = fdesign.rsrc(L,M,RESPONSE,SPEC)
constructs
object D
and sets its Specification
property
to SPEC
. Entries in the SPEC
represent
various filter response features, such as the filter order, that govern
the filter design. Valid entries for SPEC
depend
on the design type of the specifications object.
When you add the SPEC
input argument, you
must also add the RESPONSE
input argument.
D = fdesign.rsrc(L,M,SPEC,specvalue1,specvalue2,...)
constructs
an object D
and sets its specifications at construction
time.
D = fdesign.rsrc(...,Fs)
provides
the sampling frequency of the signal to be filtered. Fs
must
be specified as a scalar trailing the other numerical values provided. Fs
is
assumed to be in Hz as are all other frequency values provided.
D = fdesign.rsrc(...,MAGUNITS)
specifies
the units for any magnitude specification you provide in the input
arguments. MAGUNITS
can be one of
'linear'
— specify the magnitude
in linear units.
'dB'
— specify the magnitude
in dB (decibels).
'squared'
— specify the
magnitude in power units.
When you omit the MAGUNITS
argument, fdesign
assumes
that all magnitudes are in decibels. Note that fdesign
stores
all magnitude specifications in decibels (converting to decibels when
necessary) regardless of how you specify the magnitudes.
design
 designmethods
 fdesign.rsrc
 fdesign.interpolator
 setspecs
 fdesign.arbmag
 fdesign.arbmagnphase