Reasons for bad training performance using prioritized experience replay compared to uniform experience replay using DDPG agent

19 views (last 30 days)
I am currently trying to use prioritized experience replay while training DDPG agent on Quadruped robot (Quadruped Robot Locomotion Using DDPG Agent - MATLAB & Simulink (mathworks.com) ) instead of uniform experience replay to have faster training time. But while training with prioritized experience replay i notice considerable variance and instability while training compared to uniform replay buffer. This can be seen with frequent spikes and drops in the training monitor. The image below is when i use prioritized experience replay with following parameters
agentOptions = rlDDPGAgentOptions();
agentOptions.SampleTime = Ts;
agentOptions.DiscountFactor = 0.99;
agentOptions.MiniBatchSize = 256;
% agentOptions.ExperienceBufferLength = 1e6;
agentOptions.TargetSmoothFactor = 1e-3;
agentOptions.MaxMiniBatchPerEpoch = 200;
agentOptions.NoiseOptions.StandardDeviation = 0.1;
agentOptions.NoiseOptions.MeanAttractionConstant = 1.0;
agentOptions.ActorOptimizerOptions.Algorithm = "adam";
agentOptions.ActorOptimizerOptions.LearnRate = 1e-3;
agentOptions.ActorOptimizerOptions.GradientThreshold = 1;
agentOptions.CriticOptimizerOptions.Algorithm = "adam";
agentOptions.CriticOptimizerOptions.LearnRate = 1e-3;
agentOptions.CriticOptimizerOptions.GradientThreshold = 1;
initOpts = rlAgentInitializationOptions(NumHiddenUnit=256);
agent = rlDDPGAgent(obsInfo,actInfo,initOpts,agentOptions);
agent.ExperienceBuffer = rlPrioritizedReplayMemory(obsInfo,actInfo);
resize(agent.ExperienceBuffer,1e6);
agent.ExperienceBuffer.NumAnnealingSteps = 1e4;
agent.ExperienceBuffer.PriorityExponent = 0.6;
agent.ExperienceBuffer.InitialImportanceSamplingExponent = 0.4;
And the image below is when i use uniform experience replay for your comaparision.
Therefore im not sure why this is happening. I even tried with different hyperparameters for the prioritized experience replay but observe similar training results. Any posible solution would be really helpful.

Answers (1)

Kaustab Pal
Kaustab Pal on 8 Aug 2024
Prioritized Experience Replay (PER) tends to outperform uniform experience replay in environments where rewards are sparse, delayed, or where the dynamics are non-stationary. However, in the case of quadruped robot locomotion, the rewards are consistent. We receive positive rewards at every time-step to avoid early termination and additional rewards for positive forward velocity.
Since rewards are given consistently at every time-step, the variance in the importance of different experiences is lower. This means that each experience contributes relatively equally to the learning process, making uniform sampling sufficient for effective learning. The continuous nature of the rewards also ensures that the agent receives regular feedback about its performance, reducing the need for prioritizing specific experiences.
Because of these reasons, you can observe that the reward plot with uniform experience replay is smoother compared to the reward plot using prioritized experience replay.
Hope this clears your doubt.
With regards,
Kaustab Pal
  2 Comments
Gaurav
Gaurav on 8 Aug 2024
Hi Kaustab,
Thank you for the detailed explanation. I have a further question regarding the use of Prioritized Experience Replay (PER). While I understand that PER may not always outperform uniform sampling in certain cases, I was under the impression that it should at least have a similar training performance. However, in my situation, when I use PER, the training rewards remain consistently low, with sudden drops in performance, which I find difficult to understand. Could you clarify why this might be happening?
Additionally, could you suggest other approaches to accelerate training or potential modifications to the current simulation that might better demonstrate the advantages of PER?
Thank you!
Pavl M.
Pavl M. on 13 Oct 2024
Can you explain consistently what next parameters means:
agent.ExperienceBuffer.PriorityExponent = 0.6;
agent.ExperienceBuffer.InitialImportanceSamplingExponent = 0.4;
?

Sign in to comment.

Products


Release

R2024a

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!