# saleh shlimet

Followers: 0 Following: 0

**Statistics**

**MATLAB Answers**

**13** Questions

**0** Answers

RANK**240,937**

of 290,875

REPUTATION**0**

CONTRIBUTIONS

**13** Questions

**0** Answers

ANSWER ACCEPTANCE **
30.77%
**

VOTES RECEIVED**0**

RANK

of 19,721

REPUTATION**N/A**

AVERAGE RATING**0.00**

CONTRIBUTIONS**0** Files

DOWNLOADS **0**

ALL TIME DOWNLOADS**0**

RANK

of 145,475

CONTRIBUTIONS

**0** Problems

**0** Solutions

SCORE**0**

NUMBER OF BADGES**0**

CONTRIBUTIONS**0 Posts**

CONTRIBUTIONS**0** Public Channels

AVERAGE RATING

CONTRIBUTIONS**0** Highlights

AVERAGE NO. OF LIKES

**Feeds**

Question

How can I obtain the difference between two data stored in workspace?

I experimentally tested a motor and the measured speed and the reference speed were stored in the workspace. My supervisor aske...

6 months ago | 1 answer | 0

### 1

answerQuestion

How to execute the same code for a specific time?

I want to estimate the shaft speed of a motor and to do that I obtain the speed error between the reference speed and the estima...

1 year ago | 1 answer | 0

### 1

answerQuestion

Position error of motor shaft

I want to obtain the position error of motor shaft so I subtracted the estimated position from the measured position. modulus f...

1 year ago | 1 answer | 0

### 1

answerQuestion

how to export varied variable to saturation block in Simulink?

I tried to use varied value in the Saturation block and this value (called flux) exported from the output of a lookup table? I u...

1 year ago | 1 answer | 0

### 1

answerQuestion

Use a command only once

I use a code to search for an accurate rotor position. I used an initial value for the position (theta_b=0) as shown below and t...

1 year ago | 2 answers | 0

### 2

answersQuestion

Code error in MATLAB function block.

I wrote a code in a MATLAB function block that consists of two inputs one input for the signal that needs to be filtered and the...

2 years ago | 1 answer | 0

### 1

answerQuestion

Calculate cycle time for a signal by code

I want to calculate the cycle time for a signal (the frequency) by using a code (Matlab function block). For examble, in a motor...

2 years ago | 0 answers | 0

### 0

answersQuestion

Why the amplitude of the 90 shifted phase signal when use the analytic signal block is not equal to the original signal?

I could manage to shift the phase of signal by 90 by using analytic signal block. But, the problem is that its amplitude is not ...

4 years ago | 1 answer | 0

### 1

answerQuestion

how to shift phase of unknown frequency signal by 90 by using hilbert transform?

I tried to shift an unknown frequency signal by 90 by applying hilbert transform comand (imag(hilbert(x)) in matlab function blo...

4 years ago | 0 answers | 0

### 0

answersQuestion

How to connect simulink blocks with RF blocks (interface)?

I tried to use simulink blocks with RF blocksets but they can not be connected to each other. I think there is an interface betw...

4 years ago | 1 answer | 0

### 1

answerQuestion

How to shift a signal in simulink by 90 degrees?

I want to shift a signal by 90 degrees. there is a block called phase shift in RF blockset, but it cannot be used with simulink....

4 years ago | 1 answer | 0

### 1

answerQuestion

A problem with the solver

A problem with the solver when I run a model. when I disconnect the gate driver (simulink) from the inverter (simcap) the proble...

4 years ago | 1 answer | 0

### 1

answerQuestion

measuring the phase to neutral voltage in PMSM

in the MATLAB, how can I measure the voltage between the phase and the neutral point in the PMSM machine? (there is no access to...

4 years ago | 1 answer | 0